Free Shipping for orders over $50

SNELL Foundation Helmet Safety Standards Explained

by Jim Bartlett May 18, 2016

What are Snell Foundation Helmet Safety Standards for Action Sports Helmets?

The Snell Memorial Foundation is a nonprofit organization dedicated to research, education, testing, and development of helmet safety standards. Founded in 1957, the Snell Foundation began issuing auto racing helmet standards, followed by motorcycle, bicycle, equestrian, ski, and other helmet standards. Snell's standards are the most demanding of any helmet certification. Helmets must first pass Snell certification testing by Snell technicians in Snell labs to qualify for Snell programs. Then samples of these helmets regularly acquired directly from retailers and distributors must continue to pass test requirements in order to retain Snell certification. Testing helmets acquired on the consumer market forces manufacturers to be careful about quality control. The relevant Snell Foundation standards for action sport helmets include:
  • Snell B-90/95, Snell N-94: Bicycle helmets
  • Snell RS-98 or S-98: Ski helmets

The Snell Foundation Testing Process in Brief

Snell technicians conduct a variety of tests to determine the helmet's performance and ability to stay on the head in different environmental conditions, including ambient, wet, heat, and cold. Depending on the application and the standard, each helmet must pass all or some of the following tests. Snell bicycle helmet standards look at four aspects of a helmet:
  • Impact management - how well the helmet protects against collisions with large objects.
  • Positional stability - whether the helmet will remain in place
  • Retention system strength - whether the chins straps are strong enough to keep the helmet in place
  • Extent of protection--how much of the head is covered by the helmet

Impact Test

This test involves a series of controlled impacts where a helmet is positioned on a metal head form and then dropped in a guided fall onto various steel test anvils to simulate different impact surfaces. If the peak acceleration imparted to the head form exceeds certain threshold value, typically around 300 G's ("G" gravitational units), depending on standard and test type, the helmet is rejected.

  • Positional Stability (Roll-Off) Test: In this test, the head form is mounted on a stand and the helmet straps and buckles adjusted to obtain a "best fit." The technician places a weighted rope onto the helmet, which is then dropped, placing a rotational load on the helmet. The helmet may shift but must not roll off the head form. This test is done from two different angles.
  • Dynamic Retention Test: The Dynamic Retention Test tests the strength of the helmet chinstrap and buckle. The jaw piece is loaded with a 23 kg weight for approximately one minute. The retention system is tested by simultaneously removing the 23 kg weight and applying a 38 kg mass in an abrupt guided fall. The retention system fails if it cannot support the mechanical loads or if the retention system stretches more than 30 mm. The drop heights differ depending on the helmet standard being measured.
  • Chin Bar Test: The chin bar test measures the strength of the chin bar portion of full face motorcycle, special application racing, and kart racing helmets. The helmet is fixed to a rigid base with the chin bar facing upward. A 5 kg weight is dropped on the central portion of the chin bar.
  • Shell Penetration Test: The shell penetration test applies to motorcycle, special application racing, kart racing, skiing, and equestrian helmets. A 3 kg sharply pointed striker is dropped in a guided fall onto the helmet, which is fixed to a rigid base. The test striker must not penetrate the helmet or even achieve momentary contact with the head form.
  • Face shield Penetration Test: The face shield penetration test applies to full face motorcycle, special application racing, and kart racing helmets. The face shield is affixed to the helmet and shot along the center line in three separate places with an air rifle using a sharp soft lead pellet.
  • Flame Resistance Stand: The flame resistance test applies to special application racing helmets only. The test is conducted using a propane flame of approximately 790 degrees centigrade that is applied to the shell, trim, chin strap and face shield for a specified number of seconds, and any resulting fire must self extinguish within a specified time after flame removal.

What If My Helmet Doesn't Meet Snell Standards?

It is common to find motorcycle helmets that bear the Snell safety standard. Bicycle helmets, especially those sold in the United States, are less likely to have undergone Snell Foundation testing because:
  • The Snell testing is a longer, more stringent process and includes testing of helmets purchased on the consumer market
  • The Snell testing procedure for bicycle helmets is similar to the CPSC bicycle helmet test process. The US government requires bicycle helmets to meet CPSC standards. It's more expedient for manufacturers to test to the required standard.

RELATED ARTICLES

We hope you found this article helpful. Learn about the US CPSC bicycle helmet safety standard, and ASTM helmet safety standards on our Helmet Gear Guide Home Page.

Learn More About: Bicycle Helmets Learn More About: BMX Learn More About: Certifications Learn More About: Helmets Learn More About: Mountain Bike Helmets Learn More About: Mountain Biking Learn More About: Skiing Learn More About: Snowboarding




Jim Bartlett
Jim Bartlett

Author

Founder of XSportsProtective, snowboarder, mountain biker, father of four young kids who love action sports.


Leave a comment

All comments will be reviewed before posting.


Also in Protective Gear News

Product Spotlight: Bell Super 3R MIPS and Giro Blok Goggle Lock Up
Product Spotlight: Bell Super 3R MIPS and Giro Blok Goggle Lock Up

by Douglas DiLillo May 22, 2017

Bike season is here! To celebrate, here at SportsProtective we are offering a deal that is too good to pass up. The Bell Super 3R MIPS Full Face Helmet and the Giro Blok Goggles come together in a "Lock Up" that will offer significant savings. Learn more about both products and why they go well together in our latest Product Spotlight.

Continue Reading →

Top Picks: Full Face Helmets for MTB and BMX Under $100
Top Picks: Full Face Helmets for MTB and BMX Under $100

by Douglas DiLillo May 11, 2017

We know not all riders have an infinite budget. This "Top Picks" post tackles full face helmets at a value, meaning under $100 dollars.

Continue Reading →

Brand Focus: G-Form Pads and Armor
Brand Focus: G-Form Pads and Armor

by Douglas DiLillo May 09, 2017

G-Form is a unique brand it that it only has one technology and builds its products from it. RPT Technology is the basis of their business. Learn more about G-Form, their technology, and products in our newest Brand Focus.

Continue Reading →